- Το προϊόν Hepatitis test HCV έχει αφαιρεθεί από το καλάθι σας επειδή δεν είναι πια διαθέσιμο προς αγορά. Παρακαλούμε, επικοινωνήστε μαζί μας αν χρειάζεστε βοήθεια.
- Το προϊόν Αντικειμενοφόρες Πλάκες HistoBond®+ Adhesive έχει αφαιρεθεί από το καλάθι σας επειδή δεν είναι πια διαθέσιμο προς αγορά. Παρακαλούμε, επικοινωνήστε μαζί μας αν χρειάζεστε βοήθεια.
- Το προϊόν Αντικειμενοφόρες Πλάκες HistoBond®+S έχει αφαιρεθεί από το καλάθι σας επειδή δεν είναι πια διαθέσιμο προς αγορά. Παρακαλούμε, επικοινωνήστε μαζί μας αν χρειάζεστε βοήθεια.
Σταθμός Μέτρησης Κβαντικής Απόδοσης (Quantum Efficiency Measurement Station)
Σταθμός Μέτρησης Κβαντικής Απόδοσης: Αυτοματοποιημένο, πλήρες εργαλείο για τον χαρακτηρισμό φωτοβολταϊκών κυψελών, με μέτρηση κβαντικής απόδοσης και βασικών παραμέτρων απόδοσης.
Quantum Efficiency Measurement Station
The Quantum Efficiency Measurement Station is a complete experimental setup for solar cells spectral response investigation. The sample is illuminated with a monochromatic beam produced by the Monochromator with two types of light sources at the entrance: Xenon Lamp and Halogen Lamp. Both lamps provide wavelengths range that covers UV, VIS, and IR light. Instrument with the BIAS Light extension enables to excite the sample with a normalized white AM1.5G light from an additional Xenon Lamp combined with the Air Mass Filter. The examined cell is placed on a motorized vacuum XY Table, with a manual Z shift.
Measurements are performed in a chamber that screens the setup from ambient light and external EM fields. The incident light intensity is monitored with a Dual Band Si/InGaAs Photodiode. All the system components are fully automated, controlled via software.
⬛ Quantities measured by the instrument:
- I-V characteristics
- Open Circuit Potential (OCP) under illumination
- Spectral reflection coefficient (R)
- Spectral transmission coefficient (T)
⬛ Characteristics:
- External quantum efficiency (EQE or IPCE)
- Internal quantum efficiency (IQE or APCE)
- Short-circuit current density (Jsc)
- Fill Factor
QE Measurement Station modules
⬛ The system consists of:
- Sample Chamber
- Motorized Multi-Axis Vacuum Table with a built-in photodiode
- Integrating Sphere
- Monochromator with two entrance slits for automatic switching between light sources
- Xenon Lamp at the first entrance of the Monochromator
- Halogen Lamp at the second entrance of the Monochromator
- Lock-in for measured signals processing
- Xenon Lamp + AM1.5G Filter (BIAS Light extension)
⬛ Sample Chamber interior
⬛ Photocurrent measurement / Reflected flux measurement / Built-in photodiode for Transmitted flux measurement
Specifications
*Instrument performance may be tailored to the certain requirements
⬛ General
- Total wavelengths range: 200 ÷ 1650 nm
- Adjustable white light beam intensity on the sample: 0.01 ÷ 0.1 W/cm²
- Illumination homogeneity: 10%
⬛ Xenon Lamp
- 150 W xenon burner
- Water cooling system
- Low EM emission igniter
- Stabilization modes:
– electric current stabilization (distortions < 1%)
– electric power stabilization
– light intensity stabilization (unique solution to provide constant sample illumination during the experiment) - Maximum radiation intensity on the sample: 35 mW/cm²
⬛ Halogen Lamp
- Electrical power of halogen bulb: 150 W
- Reflector type: elliptic
- Air cooling system
⬛ Monochromator
- Three gratings on the turret, each optimized for different wavelengths range
- Automated grating switching depending on the wavelength selection
- Motorized output and input slits, controlled via software
- Two input slits for different light sources, switched via software
- Entrance and output slit opening range: 0 ÷ 5 mm
- Motorized internal shutter, that provides full cut off of the light beam
- Maximal spectral resolution: 0.1 nm (depends on the input and output slits width)
- Chopper at the output
⬛ Filter Changer
- Placed at the Sample Chamber entrance
- Up to 6 filters
- Two edge (long pass) filters provided by default: 400 nm and 600 nm
⬛ Detectors
Dual Band Si/InGaAs Photodiodes are used to monitor the incident light intensity, the flux transmitted through the sample, and the flux reflected by the sample
⬛ Lockin
- Bias potential range: -5 V ÷ 5 V
- Current ranges: 1 µA, 10 µA, 100 µA, 1 mA, 10 mA, 100 mA
- Current resolution: from 1 pA to 100 nA (range dependent)
- Maximum sampling rate: 1 kSample/s
- Connection with PC: via USB 2.0
- Two photodiodes inputs handled simultaneously (Reference Photodiode and Reflectance/Transmittance Photodiode)
- DC and AC measurement mode
- Input gain: x1, x2, x4, x8, x12
- Integration time: 1 ms ÷ 10 s
⬛ Motorized Multi-Axis Vacuum Table
- Maximum sample dimensions: 20 x 20 cm
- Contact electrodes placed manually at any point of the sample
- Golden coating
- Movement range for Z axis: 12 mm (manual)
- Movement precision: 0.01 mm
- Built-in detector for transmitted light detection
- Adjustable contact pins for photocurrent measurements
- Vacuum pump integrated to keep the sample in stable position
